温馨提示×

温馨提示×

您好,登录后才能下订单哦!

密码登录×
登录注册×
其他方式登录
点击 登录注册 即表示同意《亿速云用户服务条款》

Juniper SRX策略路由总结

发布时间:2020-07-21 18:01:17 来源:网络 阅读:24491 作者:caichuanhui 栏目:网络安全

1、路由实例

路由实例是路由表、接口和路由协议参数的集合。通过设置接口及路由协议各种参数可以形成路由实例的路由表。

每个路由实例都有自己的实例名称,并且各自维护一张独立的路由表。

全局路由其实也是一个路由实例,其实例名称为inet.0。


2、普通静态策略路由(只做策略,不作NAT转换)

Juniper SRX策略路由总结

设置包括如下步骤:

1)设置应用接口子接口,定义为服务区域的入接口/出接口

2)定义路由实例,实例类型为forwarding,实例路由表

3)定义过滤器firewall filter

4)定义接口路由组rib-group;

5)将接口路由组导入到全局路由表及路由实例的路由表中;

6)在内网接口应用过滤器filter


3、做NAT的静态策略路由(既做策略又做NAT转换)

注意:

1)该情况下需要试用virtual-router类型的路由实例

2)每个virtual-router维护一张独立的路由表


配置实例拓扑图

Juniper SRX策略路由总结


达到目的:

默认内网主机上网走CNC 2M链路访问公网,指定的PC走CNC 50M链路访问外网


实现思路:

默认内网所有主机通过全局路由表inet.0走CNC 2M链路出局访问公网,部分指定的PC通过Juniper SRX的FBF路由策略走路由实例的路由表出局访问公网


设置步骤如下:

1)定义服务区域zone

配置示例:

set security zones security-zone lt host-inbound-traffic system-services all

set security zones security-zone lt host-inbound-traffic protocols all


2)设置应用接口子接口,定义为服务区域的入接口/出接口

配置示例:

set security zones security-zone lt interfaces ge-0/0/2.0 host-inbound-traffic system-services all

set security zones security-zone lt interfaces ge-0/0/2.0 host-inbound-traffic protocols all


3)定义路由实例,路由实例数量可根据接入的ISP线路数量来定义。实例类型为virtual-router,VR的虚拟接口,VR的路由表

配置示例:

set routing-instances CNC50M instance-type virtual-router

set routing-instances CNC50M interface ge-0/0/2.0

set routing-instances CNC50M routing-options static route 0.0.0.0/0 next-hop XX.XX.XX.XX  ##指向ISP提供的公网网关


4)定义NAT的相关映射rule-set、rule,策略policy、address-book、application等

√Source NAT的rule-set 配置示例:

set security nat source rule-set CNC50M-snat-internet from zone trust

set security nat source rule-set CNC50M-snat-internet to zone lt

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside match source-address 0.0.0.0/0

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside match destination-address 0.0.0.0/0

set security nat source rule-set CNC50M-snat-internet rule CNC50M-inside-to-outside then source-nat interface

√ 策略policy 配置示例:

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match source-address CBGZ-out-norestrict

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match destination-address any

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet match application any

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then permit

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then log session-init

set security policies from-zone trust to-zone lt policy CNC50M-snat-internet then log session-close


5)定义过滤器filter

配置示例:

set firewall family inet filter filter-1 term LAN_term from destination-address 172.16.0.0/16

set firewall family inet filter filter-1 term LAN_term from destination-address 172.20.0.0/16

set firewall family inet filter filter-1 term LAN_term from destination-address 192.168.0.0/16

set firewall family inet filter filter-1 term LAN_term then accept     ##允许内网PC互访,不作以上配置将会导致网关为此防火墙内网接口的PC无法访问内网其他PC。


##指定的PC从CNC 50M链路出局访问公网

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.29.25/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.29.251/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.166/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.137/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.139/32

set firewall family inet filter filter-1 term CNC50M_term from source-address 172.16.28.138/32

set firewall family inet filter filter-1 term CNC50M_term then routing-instance CNC50M


set firewall family inet filter filter-1 term default then accept ##对于filter的其他数据,采取默认动作accept(接受)


6)定义接口路由组

配置示例:

set routing-options interface-routes rib-group inet INSIDE


7)将接口路由组导入到全局路由表及实例的路由表中

配置示例:

set routing-options rib-groups INSIDE import-rib inet.0

set routing-options rib-groups INSIDE import-rib CNC50M.inet.0

set routing-options rib-groups INSIDE import-rib default.inet.0


8)在内网接口应用相应的过滤器filter

set interfaces ge-0/0/0 unit 0 family inet filter input filter-1


4、普通静态策略路由与NAT转换的策略路由之间的区别

路由实例类型不同:

普通静态策略路由类型:forwarding

NAT转换的策略路由类型:virtual-router


参考链接:http://www.docin.com/p-598358767.html


向AI问一下细节

免责声明:本站发布的内容(图片、视频和文字)以原创、转载和分享为主,文章观点不代表本网站立场,如果涉及侵权请联系站长邮箱:is@yisu.com进行举报,并提供相关证据,一经查实,将立刻删除涉嫌侵权内容。

AI