话说临近国庆，项目前期眼看瞅着就要接近尾声，用户要在国庆前一天就要搬进新楼，享受空调WIFI美食,
某公司的采购周期是出了名的长，但无线AP，AC还没到货怎么办？领导坐不住了，急吼吼的问网工：
小灰啊，这款EWP-WA2610H-FIT 京东上有没有现货？“我查查，还真有”
“好，没有AC控制器能不能玩的转？” “我来查一查，瘦AP转胖AP是可以行的通的”
（我感觉领导这话根本就不是问句啊...理论上可以啊，毕竟小灰以前见过瘦转胖的目录）
“ 好，明天下午就能到货，还剩一天半时间了。抓紧。”
领导另辟蹊径，AP采购的事顺利拿下，下面该我出马了。
瘦转胖AP容易，网上不有案例吗？
不容易...
第一，刚买回来的瘦AP是没有配置的！没有配置的！没有配置的！（重要的话说三遍 ）
要先通过AC将脚本配置传输到AP。怎么办？还好三期的AC WX3520H还能一用，
（将一个楼层的交换机其余端口shutdown,释放license的招儿我也想出了）
说干就干，把AC分配好网段给AP,AP顺利拿到地址，再通过TFTP方式传输倒入胖版本不就搞定了吗？
( 呵呵，年轻人想法还是简单 )
一看AP配置傻了，没有TFTP命令！什么，FTP也没有？WTF
也不看看WX 3520H 是什么货？（采用H3C全新一代Comware V7网络操作系统平台（以下简称V7系统））
倒入WA 2610H 那是V7版本啊？(so what?) WA2610H V7胖版本没有开发出来！只有V5的，
所以没有TFTP命令行倒入V5胖版本。
怎么办？
华三V7瘦AP转V5胖AP。曲线救国。
部分重要脚本配置如下：interface Ethernet1/0/2
port access vlan 1000
port-isolate enable ##端口隔离 2口，3口不能互相访问
dis wlan ap name 模板名字(默认是AP的mac地址) verbose ##查看AP获取的地址
AC:wlan ap-execute 模板名字 exec-console enable ##开启telnet AP的权限
AP的默认password :h4capadmin
V7的H3C AC 3520H版本，下发给H3C EWP-WA2610H-FIT V7版本，
现在要把WA 2610H-FIT AP V7从瘦AP 切到 胖AP V5版 （H3C WA2610H 胖V7版本没开发出来）
WA2610H
打开设备外壳，里面有一个mini console 口 （有个迷你console口，good ）
找到手机usb数据线(即一般手机数据传输充电线) console线就是原来安卓充电器用的那种传输线！
Usb端链接电脑，另一端链接 ap
http://www.h4c.com/cn/d_201302/774009_30005_40.htm
驱动安装好后，电脑通信端口会生成一个com口
电脑通过crt登录设备命令行
参考如下文档将v7瘦版本切成v5胖版本
参考案例：
问题现象
某局点现场一台V7的WA4320H-ACN设备，由于现有的AC设备上的license数量不足，需要将AP切换为胖AP使用。了解现场工程师的需求后，我们立即查找相应的资料并查找解决方法。经过查找资料确认该型号的AP胖版本只有V5的版本，所以需要将V7的瘦版本降级为V5的胖版本。
告警信息
经过查找官网软件版本后确认，该型号的AP仅有V5的胖版本
原因分析
该型号V7版本的瘦AP经过查阅资料确认，没有可以使用的V7的相应的适配胖版本，和现场工程师协商建议其将该AP降级为V5的胖AP。
解决办法
引导工程师做V7瘦版本降级V5胖版本的操作，操作过程如下:
在AP的启动过程中
按下Ctrl+B进入AP的BOOTROM菜单
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : May 15 2017
CPU Type : ATHEROS AR9531
CPU L1 Cache : 32KB
CPU Clock Speed : 650MHz
Memory Type : SDRAM
Memory Size : 128MB
Memory Speed : 450MHz
BootWare Size : 512KB
Flash Size : 16MB
PCB Version : Ver.A
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Download Files(.) |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu
============================================================================
Enter your choice(0-4): 4
| ==========================<ETHERNET PARAMETER SET>========================== |
Note: '.' = Clear field. | '-' = Go to previous field. |
|---|
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :host
:wa4300s_fat.bin ###导入已经下好的V5胖版本
Target File Name :target
:wa4300s_fat.bin
Server IP Address :192.168.1.1 192.168.0.20 （电脑IP）
Local IP Address :192.168.1.253 192.168.0.30 (AP IP)
Subnet Mask :0.0.0.0 255.255.255.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Download Files(.) |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 1
Loading.....................................................................
............................................................................
............................................................................
..Done.
11293696 bytes downloaded!
Extended BootWare Version is not equal,updating? [Y/N]Y ###此处开始boot版本替换,选Y
Updating Extended BootWare..........Done.
Basic BootWare Version is not equal,updating? [Y/N]Y ###选Y
Updating Basic BootWare..........Done.
BootWare updated,System is rebooting now.
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare....
The Extend BootWare is self-decompressing.........................Done!
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : Jun 19 2017
CPU Type : ATHEROS AR9531
CPU L1 Cache : 32KB
CPU Clock Speed : 650MHz
Memory Type : SDRAM
Memory Size : 128MB
Memory Speed : 450MHz
BootWare Size : 512KB
Flash Size : 16MB
PCB Version : Ver.A
Check net params crc error, use the default value
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
============================================================================
Ctrl+C: Display Copyright
Ctrl+F: Format File System ###执行Ctrl+F格式化操作
Enter your choice(0-9):
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
..................
Format success. ###第一次TFTP传文件后格式化
###如果这边不停的格式化，然后重启进入系统，AP就有可能玩坏了。进入到一种貌似是胖AP但console操控不了的局面，貌似就因此玩坏了一个AP..
所以说瘦AP切胖AP真是有风险的！
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
============================================================================
Ctrl+C: Display Copyright
Ctrl+F: Format File System
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 3
Protocol (FTP or TFTP) :tftp
Load File Name :host
:wa4300s_fat.bin ###替换系统版本为胖版本
Target File Name :target
:wa4300s_fat.bin
Server IP Address :192.168.1.1 192.168.0.20
Local IP Address :192.168.1.253 192.168.0.30
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 2 ### ###第二次TFTP传输后 Update Main Application File 升级主应用程序文件！
Loading.....................................................................
............................................................................
............................................................................
..Done!
11293696 bytes downloaded!
Updating File flash:/wa4300s_fat.bin........................................
............................................................................
...........................................................Done!
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Application Program To SDRAM And Run |
|<2> Update Main Application File |
|<3> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-3): 0
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
============================================================================
Ctrl+C: Display Copyright
Ctrl+F: Format File System
Enter your choice(0-9): 0
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare....
The Extend BootWare is self-decompressing.........................Done!
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : Jun 19 2017
CPU Type : ATHEROS AR9531
CPU L1 Cache : 32KB
CPU Clock Speed : 650MHz
Memory Type : SDRAM
Memory Size : 128MB
Memory Speed : 450MHz
BootWare Size : 512KB
Flash Size : 16MB
PCB Version : Ver.A
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Starting to get the main application file--flash:/wa4300s_fat.bin!..........
............................................................................
............................................................................
..........
The App file is self-decompressing..........................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
...........................................................Done!
System application is starting...
Startup configuration file does not exist.
User interface con0 is available.
Press ENTER to get started.
<WA2610H>
#Jan 1 00:00:26:418 2009 WA2610H SHELL/4/LOGIN:
Trap 1.3.6.1.4.1.25506.2.2.1.1.3.0.1<hh4cLogIn>: login from Console
%Jan 1 00:00:26:418 2009 WA2610H SHELL/5/SHELL_LOGIN: Console logged in from con0.
<WA2610H>
<WA2610H>
<WA2610H>
<WA2610H>dis ip int bri
<WA2610H>dis ip int brief
down: administratively down
(s): spoofing (l): loopback
Interface Physical Protocol IP Address Description
Vlan1 up up 192.168.0.50 --
<WA2610H>sys
System View: return to User View with Ctrl+Z.
[WA2610H]qu
<WA2610H>save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
Validating file. Please wait.......
Configuration is saved to device successfully.
<WA2610H>y
^
% Unrecognized command found at '^' position.
<WA2610H>
<WA2610H>sys
System View: return to User View with Ctrl+Z.
[WA2610H]int vlan 1
[WA2610H-Vlan-interface1]ip add 192.168.0.118 24
[WA2610H-Vlan-interface1]qu
[WA2610H]qu
<WA2610H>save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait........
%Jan 1 00:00:57:227 2009 WA2610H WMAC/6/WMAC_CHANNEL_CHANGE: Channel change for APID 1, RadioId 1 from channel 0 to channel 11...
Configuration is saved to device successfully.
<WA2610H>
<WA2610H>
顺利拿到胖AP就没有坑了吗？
NO WAY .
配置胖AP，先打开无线任务，接入任务，新建SSID等功能子项，注意，密码千万要输正确咯。
绑定射频，开启后 发现，安卓手机能用，苹果手机用不了！
为啥？是不是加密方式有问题，
原来是DHCP池没有配DNS，苹果手机跟国产手机不通，没有DNS就认为网络不能用~
以上的坑印象最深，还有就是跳线会接触不良导致传输时断时续，刚开始AP获取IP时端口频繁UP,DOWN是正常的，要有耐心...
这次调AP确实遇到了坑，也怪我无线经验太少，加上又是时间紧张，饭没吃，觉没睡了，现在回想也是酸爽...还好顺利完成任务，回想起来那些坑倒是意犹未尽呐！
免责声明：本站发布的内容（图片、视频和文字）以原创、转载和分享为主，文章观点不代表本网站立场，如果涉及侵权请联系站长邮箱：is@yisu.com进行举报，并提供相关证据，一经查实，将立刻删除涉嫌侵权内容。
